Running Windows 2008 (runtime) off a USB Drive Without VHD

This post describes installing MS-Windows 2008 on a USB Drive without the help of a Virtual Hard Drive (VHD). In an earlier post I described how to do this WITH a VHD.

Installing windows onto a USB device requires quite some steps. In what situations this is possible I cannot say, but it obviously works in some.

Below is a description of a Windows 7 installation setting up a new USB HardDisk with "Hyper-V Windows Server 2008 R2".
Let's take every single step into account.

(Intermezzo's are used to show errors you would get when skipping steps. One of them is important.)

Assumptions
Your USB HDD drive letter is going to be "U:".
Your DVDDrive has drive letter "V:".
You have administrator rights.

Tools needed
Your Windows Installation Disk.
BootSect.exe (can be found in the "Boot" directory of your windows install disk).
Windows Automated Installation Kit (WAIK) (Needed for ImageX).

Steps
1 - You will need access to the BIOS setup.
Make sure that your BIOS supports booting into a USB device.

2 - If you've got a brand new drive, you will need to initialize it. You can do this in Window's Disk Management tool, which is available in all windows versions.

Make sure you choose for NTFS. Give it a drive letter (we need it later). For the rest of this tutorial, I will assume drive letter "U:".

INTERMEZZO:
Trying to boot from the USB Drive will now give the following error.

Non-System disk or disk error.
Replace and strike any key when ready.

3 - Make sure the partition on the USB HDD that you wish to install in is Active. You can do this in de Windows Disk Management.
(This step got me going for a while……)
Note that the option to mark the partition as active will be greyed out if the partition is active by default.

4. Install WAIK. You should now have three "ImageX" executables (one for AMD64, one for Intel64, and one for 32 bits.) These can be found in C:\Program Files\Windows AIK\Tools.

NOTE: For me the only one working was the AMD version, although I have an Intel T5500 processor !!?!??!?!

5 - Open an elevated command prompt.
Go to the correct WAIK directory for your machine.
Type the following command (DO NOT FORGET THE DRIVELETTER:)

BootSect /nt60 U:

Note the colon.
(Bootsect.exe updates the master boot code for hard disk partitions to switch between BOOTMGR and NTLDR.)

Leave the CMD open. We'll need it again later.

IMPORTANT
We need to make sure that your machine can actually boot into the USB Drive before we continue. Make sure the USB Drive is the first to boot so that a automatic restart will go back to the USB Drive.

Try it now, and make sure you get the following error when rebooting your machine. After that, boot back into windows so you can continue with this tutorial.


INTERMEZZO:
Trying to boot from the USB Drive will now give the following error.

BOOTMGR is missing.
Press Ctrl+Alt+Del to restart.


INTERMEZZO:
If you were now trying to install Windows onto the USB Drive, you would receive the following error:

6 - In de Elevated CMD run the following:

imagex /info V:\sources\install.wim

This will show you all the entries (or versions) available in the WIM-file; Hyper-V Server 2008 R2 has only one entry; it will have "index 1". No changes have been made yet.

Remember that V: was assumed to be the drive letter of your DVD Drive (where the Windows Install disk lives).

With the previously found index number, run the following:

imagex /apply /check /verify V:\sources\install.wim 1 U:

This step takes a while, and will place a complete image of the Windows version you want to install onto the USB drive.

7 - Boot files
Let's copy the necessary boot file to the USB Drive (use the elevated DOS prompt again):

bcdboot U:\Windows /s U: /v

(Note: if this fails it may help to disconnect and reconnect the USB Drive.)

8 - Clean up
You can now close the CMD where you ran BcdBoot.

Remove your Windows Install disk from the drive. It is no longer needed.

Reboot the machine, and make sure the FIRST boot device is the USB Drive. Windows may want to reboot a few times, and it would be annoying if it would boot into the wrong version.

Boot into the USB Drive and see the magic happen.

---